Free field guide / Autumn and winter 2026/27

Winter care for fusion splicers

Cold vans, heated cabs and damp sites all change how a splicer, cleaver and stripper behave. Our free guide covers the checks that keep INNO equipment splicing well from October to March.

Free PDF, no sign-up

Read it online or download it to your phone or tablet.

15 pages, 10 sections

One working day, from overnight storage to damp equipment.

From our service bench

Based on what we see on INNO machines that come in for repair.

Written for UK winters

Cold vans, rain, brick dust and damp afternoons.

Why winter is harder on kit

Most winter faults start before the first splice

A splicer can arrive on site dry and still mist up. A dirty cleaver causes problems that look like a splicer fault. A machine that splices well at eight may need recalibrating by lunchtime.

01

Condensation

Moisture forms on cold equipment the moment it meets warmer, damper air. It settles on lenses, V-grooves and contacts, often where you can’t see it.

02

Changing conditions

Temperature, humidity and pressure all change the arc. Every move between van, cabinet and building is a different environment for the splicer.

03

Dirt and damp on site

Rain, mud and brick dust find their way into the splicing chamber and the case. Small amounts cause repeated alignment errors and high loss.

6,000 arcs

Recommended electrode replacement on current INNO splicers, or 5,500 on earlier models.

IPA 99% or higher

Cleaning alcohol with no additives, kept tightly capped.

0°C charging limit

Charge lithium-ion batteries indoors, never in a cold van overnight.

The working day

Six habits from van to splice

01

Dry storage

Kit indoors overnight, in a closed case in a dry room.

02

Secure transport

Case latched, secured and kept off a wet floor.

03

Acclimatisation

Switched off with the case shut for the first few minutes somewhere new.

04

Arc calibration

At the start of the day and whenever conditions change.

05

Sheltered work

Out of the rain and upwind of drilling or cutting.

06

Dry packing

Case and inserts checked before the kit goes back in.

Moisture and temperature

Let the splicer match the place it will work in

Off for the first few minutes

Keep it switched off with the case shut when it moves somewhere new. Allow longer for a bigger jump in temperature, such as a frosty van to a heated room.

Lenses and screen clear

Make sure the lenses and screen are clear before operation. If they are still misted, wipe the lenses with a clean cotton bud.

Batteries charged indoors

Lithium-ion packs mustn't be charged below 0°C. INNO splicers are rated for storage down to −20°C, so the cold itself is rarely the problem.

Room air at 20°C and 60% humidity has a dew point of about 12°C. A splicer that spent the night in a van at 4°C is well below that, so moisture forms on it as soon as you bring it in.

Preparing the machine

Calibrate, clean, then splice

When to run Arc Calibration

At the start of every working day, whenever the environment changes, after new electrodes and when loss becomes high or inconsistent.

Both values should read 11

Anything from 9 to 12 is acceptable. Use fresh G.652.D fibre and never multimode fibre.

Clean before you blame the splicer

Dirt on the V-grooves, press arms or cleaver shows up as alignment errors, poor cleave angles and high loss.

Arc Calibration measures how far each fibre end melts back and where the arc centre sits, then corrects the arc for the conditions.

Damp equipment

Condensation usually clears on its own

Wipe the splicer down, switch it off, take the battery out and let it dry at room temperature out of the case. Heaters, hairdryers and rice don’t speed it up. If water got inside, or you’re not sure whether it did, don’t switch it on and send it to our service centre.

The full guide

Autumn and winter care guide

Ten sections on one working day, from overnight storage to recovering damp equipment. Open it in your browser or download the PDF to keep on your phone or tablet.

Uptero Autumn and Winter Care Guide

15 pages / PDF / 4 MB

Support beyond the guide

Something not right? Talk to an engineer.

If your splicer has persistent faults, is due a service or has been exposed to moisture, get in touch and we’ll talk it through. It helps to have the serial number and any error messages to hand. We reply as soon as possible.

Questions

Winter splicing questions

How long should a splicer acclimatise before use?

There's no fixed number of minutes. A few minutes in the new environment is often enough for the splicer to stop misting and work normally. A bigger jump, such as a frosty van to a heated room, takes longer. Keep it switched off until the lenses and screen are clear.

How often should I run Arc Calibration?

At the start of every working day, whenever the working environment changes, after replacing the electrodes and whenever splice loss becomes high or inconsistent.

When should I replace the electrodes?

At about 6,000 arcs on current INNO splicers, or 5,500 on earlier models, and sooner in harsh conditions. Check the current arc count in System Information.

What should I do if my splicer gets wet?

Condensation and surface damp usually clear on their own once the splicer has dried at room temperature. If water got inside, or you're not sure whether it did, don't switch it on. Take the battery out and send it to our service centre.

Can I leave my splicer in the van overnight?

INNO splicers are rated for storage down to −20°C, so the cold is rarely the problem. Theft, damp and the morning warm-up are. Taking the kit indoors is the better option, and machines can be registered on OwnerMark™.